Search By Year,Make and Model
Internal vs. External Wastegate: How a Wastegate Works and Which One Your Turbo Build Needs
How a turbo wastegate controls boost, the difference between internal and external wastegates, when to upgrade to an external gate, and how to size and set one up. Includes Granatelli 44mm, 50mm and 60mm options.
Short answer: A wastegate controls boost by letting some exhaust bypass the turbine once you hit your target pressure. An internal wastegate is a flapper built into the turbo's turbine housing. An external wastegate is a separate valve mounted on the exhaust manifold or collector with its own dump path. Internal gates are simpler and cheaper. External gates give you more bypass capacity and more consistent boost control on modified engines, which is why most serious turbo builds use one.
If your boost keeps climbing past where you set it, or you're planning a turbo build and trying to decide on a turbo and manifold, the wastegate decision comes up fast. This guide explains how a wastegate works, the real differences between internal and external designs, when it's time to upgrade, and how to size and install an external gate. Granatelli Motor Sports builds external wastegates in 44mm, 50mm and 60mm in Oxnard, California, so we'll also show where each one fits.
How a Turbo Wastegate Works
A turbocharger is driven by exhaust. Exhaust spins the turbine, the turbine spins the compressor, and the compressor makes boost. Left alone, more exhaust means more turbine speed and more boost, until something breaks. The wastegate is the valve that stops that.
- Below target boost: A spring holds the wastegate valve shut, and all the exhaust goes through the turbine.
- At target boost: A reference line feeds boost pressure to the wastegate actuator. When that pressure overcomes the spring, the valve starts to open.
- Bypassing exhaust: Some exhaust now goes around the turbine instead of through it. The turbo stops accelerating and boost levels off.
- Adding boost: A boost controller can hold the valve shut longer so the system runs above the spring's base pressure.
The spring sets your base boost, the lowest boost the system will normally run. Our Wastegate Boost Spring & PSI Guide shows how spring ratings add up.
What Is an Internal Wastegate?
An internal wastegate is a flapper valve built into the turbine housing, opened by an actuator canister bolted to the turbo through a rod. Most factory turbo cars use one.
- Pros: Simple, compact, no extra welding or plumbing, and lower cost.
- Cons: The bypass port is limited by the size of the turbine housing, and the bypassed exhaust rejoins right at the turbine outlet. On a modified engine with more exhaust flow, an internal gate can run out of capacity, and boost creeps.
What Is an External Wastegate?
An external wastegate is a standalone valve with its own actuator, mounted on the exhaust manifold or collector ahead of the turbine. The bypassed exhaust leaves through its own dump tube, either rejoining the exhaust downstream or venting to atmosphere.
- Pros: More bypass capacity, you choose the valve size for your engine, exhaust leaves through a separate path, and it's easy to service or swap springs.
- Cons: Needs a manifold or collector with a wastegate flange, welding, a dump tube and reference lines. More parts and more fabrication.
Internal vs. External Wastegate: Side-by-Side
| Internal wastegate | External wastegate | |
|---|---|---|
| Location | Built into the turbine housing | Separate valve on the manifold or collector |
| Bypass capacity | Limited by turbine housing design | Set by the valve size you choose (for example 44, 50 or 60mm) |
| Boost creep risk on modified engines | Higher | Lower when sized and placed correctly |
| Installation | Bolt-on with the turbo | Welded flange, dump tube and reference lines |
| Cost | Lower | Higher |
| Typical use | Factory and mild bolt-on turbo cars | Custom turbo kits, high-boost and high-horsepower builds, twin-turbo systems |
When Should You Upgrade to an External Wastegate?
- Boost creep: Boost keeps climbing with RPM even though the spring should hold it. That usually means the gate can't bypass enough exhaust.
- You're running a bigger turbo or more power than the factory setup was designed for.
- You're building a custom manifold or turbo kit and can add a wastegate flange from the start.
- You want low boost on a big turbo. A large turbo on a big-displacement engine at low boost moves a lot of exhaust, and needs a lot of wastegate.
- Twin-turbo builds, where one gate per turbo or per bank is common.
How to Size an External Wastegate
Size the valve before you choose a brand or an actuator style. As a starting point for typical gasoline performance builds, Granatelli suggests:
| Valve size | Typical starting range | Good fit for |
|---|---|---|
| 44mm | About 350–700 HP | Street turbo builds, tight engine bays, twin-turbo systems running one gate per bank |
| 50mm | About 600–1,000 HP | Larger turbos and higher exhaust-flow street/strip builds |
| 60mm | About 900–1,500+ HP | Large-frame turbos, big-displacement engines, very high exhaust flow |
Those are sizing guidelines, not horsepower limits. Displacement, turbo size, target boost and manifold design all shift the right answer. If your turbo can make far more boost than you plan to run, step up a size. See 44mm vs. 50mm vs. 60mm Wastegate: What Size Do You Need? for the full walkthrough.
Piston vs. Diaphragm External Wastegates
Once the size is right, choose the actuator. A diaphragm gate uses a flexible membrane; a piston gate uses a mechanical piston. Granatelli Motor Sports builds both in every size:
| Size | Water-cooled diaphragm | Piston-actuated |
|---|---|---|
| 44mm | 540244 – $144.64 | 540261 – $256.61 |
| 50mm | 540202 – $154.61 | 540203 – $267.08 |
| 60mm | 540259 – $169.58 | 540260 – $277.55 |
Prices as of Nov 19, 2026. Every Granatelli external wastegate uses V-band mounting, ships with flanges, clamps and a spring kit, and is made in the USA. Pick the piston line for high-heat, drag and performance diesel builds or if you'd rather not run coolant lines. Pick the water-cooled diaphragm line if you want the conventional actuator, can plumb coolant, and want the lower price. Our Piston vs. Water-Cooled Diaphragm Wastegates guide compares them side by side.
External Wastegate Installation Tips
- Get the takeoff angle right. Garrett's wastegate installation guide recommends a smooth 45° takeoff and warns that a 90° takeoff can cut flow capacity by as much as half.
- Let it see every cylinder. Mount the gate on the collector or manifold where it sees exhaust from all cylinders, not just the closest one.
- Keep reference lines short and away from the turbine housing. A melted or slipped line means lost boost control.
- Use the right plumbing diagram. Port functions on a piston gate are not the same as on a diaphragm gate.
- Plan the dump tube. Rejoin the exhaust at a shallow angle downstream of the turbine, or run a screamer pipe where it's legal.
- Start with a low spring setup and log boost on the car, not on the bench.
More on location and creep: Wastegate Placement Explained.
Common Wastegate Mistakes
- Trying to fix boost creep with a stiffer spring. A stiffer spring raises base boost. It doesn't add bypass capacity.
- Undersizing on a big-displacement, low-boost build.
- Poor placement. A great gate on a bad takeoff behaves like a much smaller one.
- Mixing part numbers on a twin-gate setup. Use the same part on both sides so both gates respond the same way.
- Forgetting the intake side. The wastegate controls boost; a blow-off valve releases it when the throttle closes. Most builds need both.
Frequently Asked Questions
What does a wastegate do on a turbo?
It controls boost by letting some exhaust bypass the turbine once the target pressure is reached, which stops the turbo from spinning faster and making more boost.
What is the difference between an internal and external wastegate?
An internal wastegate is a flapper built into the turbine housing. An external wastegate is a separate valve on the manifold or collector with its own dump tube. External gates offer more bypass capacity and more consistent boost control on modified engines.
Is an external wastegate better than an internal wastegate?
For modified, high-boost and high-horsepower builds, usually yes, because it can bypass more exhaust and reduce boost creep. For a mild factory-style setup, an internal gate is simpler and costs less.
What causes boost creep?
Boost creep happens when the wastegate can't bypass enough exhaust, even fully open. Common causes are a gate that's too small for the turbo and engine, or a manifold that doesn't give exhaust a smooth path into the gate.
Can I add an external wastegate to an internally gated turbo?
Yes, with a manifold or collector that has a wastegate flange. The internal flapper then needs to be kept shut, usually by locking it closed, so the external gate does the work. Plan it with your turbo and manifold supplier.
What size external wastegate do I need?
As a starting point for typical gasoline builds, Granatelli suggests 44mm for about 350–700 HP, 50mm for about 600–1,000 HP and 60mm for about 900–1,500+ HP. Turbo size, displacement and target boost can move you up a size.
Does a wastegate set my boost level?
The wastegate spring sets the mechanical base boost. A boost controller can raise boost above that when the system is plumbed and tuned correctly.
The Bottom Line
An internal wastegate is fine on a stock or mildly modified turbo car. Once you add a bigger turbo, more boost or more power, an external wastegate gives you the bypass capacity and control to keep boost where you set it. Size the valve first, pick the actuator second, and place it on a smooth takeoff.
Granatelli Motor Sports builds water-cooled diaphragm and piston-actuated external wastegates in 44mm, 50mm and 60mm, made in the USA with V-band flanges, clamps and springs in the box. Free shipping on orders over $100, and orders placed before 3:30 PM Pacific ship the same day.
Shop Granatelli 44mm, 50mm & 60mm External Wastegates →
Written by JoJo Granatelli — third generation at Granatelli Motor Sports in Oxnard, California.

