Search By Year,Make and Model
What Does a Blow-Off Valve Do? How a BOV Works and When Your Turbo Needs One
A blow-off valve releases trapped boost when the throttle closes so it doesn't slam back into the turbo. Here's how a BOV works, what compressor surge is, how to size and set one up, and which Granatelli BOV fits your build.
Short answer: A blow-off valve (BOV) is a pressure-relief valve on the intake side of a turbocharged engine. When you lift off the throttle under boost, the throttle blade slams shut and the compressed air in the charge pipe has nowhere to go. The BOV opens and vents that air, so it doesn't push back through the turbo's compressor. That protects the turbo from compressor surge and keeps throttle transitions clean.
If you just bolted a turbo onto your build, or you're tracking down a fluttering sound every time you shift, the blow-off valve is one of the first parts to understand. It doesn't make horsepower, but it protects the most expensive part of the boost system and changes how the car drives between throttle events.
This guide explains what a blow-off valve does, how it works, how to choose and set one up, and the mistakes we see most often. Granatelli Motor Sports builds 50mm and 64mm blow-off valves in Oxnard, California, so we'll also show where each one fits.
What Happens When You Lift Off the Throttle Under Boost
A turbocharger's compressor packs air into the charge pipes, intercooler and intake manifold. At full throttle that air flows straight into the engine. The problem starts the instant you close the throttle, on a gear change or when you lift mid-corner.
The throttle blade closes, but the turbo is still spinning fast and still pushing air. The pressurized air between the compressor and the throttle body is now trapped. With nowhere to go, it reverses direction and pushes back against the compressor wheel.
What Is Compressor Surge?
Compressor surge is that reversed airflow fighting the spinning compressor. You hear it as a fluttering or chattering sound on lift-off. It loads the compressor wheel and the turbo's thrust bearing in a direction they aren't meant to handle, and it slows the turbo down, so boost takes longer to come back when you get back on the throttle.
A blow-off valve prevents that by giving the trapped air an exit before it reaches the compressor.
How a Blow-Off Valve Works
A BOV mounts on the charge pipe between the turbo and the throttle body. Inside is a valve held shut by a spring. A small vacuum/boost reference line connects the top of the valve to the intake manifold, after the throttle body.
- Under boost: The manifold is pressurized, and that pressure plus the spring holds the valve closed. All the air goes to the engine.
- Throttle closes: The manifold immediately drops into vacuum, while the charge pipe is still full of boost.
- Valve opens: Charge-pipe pressure pushes up on the valve while manifold vacuum pulls it open against the spring. The valve lifts and the trapped air is released.
- Back on the throttle: Manifold pressure returns, the spring closes the valve, and boost builds again.
Spring rate decides how easily the valve opens. Too soft and the valve can crack open at idle or leak at low boost. Too stiff and it may not open fully on lift-off, which lets some surge through. That's why most performance BOVs offer interchangeable springs or adjustable preload.
Blow-Off Valve vs. Wastegate
These two parts get mixed up constantly, but they work on opposite sides of the turbo:
- Wastegate: on the exhaust side. It controls how much boost the turbo makes by letting exhaust bypass the turbine.
- Blow-off valve: on the intake side. It releases boost that's already been made when the throttle closes.
Most turbo builds need both. Our Wastegate vs. Blow-Off Valve guide covers how they split the job, and our Internal vs. External Wastegate guide explains the exhaust side.
Atmospheric vs. Recirculating Blow-Off Valves
A BOV can send released air to one of two places:
- Atmospheric (vent-to-atmosphere): Releases air outside the intake. This is the classic "pssshh." All four Granatelli blow-off valves are atmospheric.
- Recirculating (often called a diverter or bypass valve): Routes the air back into the intake ahead of the turbo. Quiet, and common on factory turbo cars.
The choice matters most on cars with a mass airflow (MAF) sensor ahead of the turbo. That air has already been measured, so venting it can make the engine run rich on lift-off. Speed-density and many custom ECU setups don't have that problem. Our Atmospheric vs. Recirculating Blow-Off Valves guide covers that decision in detail.
How to Choose a Blow-Off Valve
1. Size it to your airflow
A bigger turbo moves more air, and more air has to escape when the throttle closes. A 50mm BOV covers most street and street/strip turbo builds. Large turbos, high boost, big charge piping and centrifugal superchargers are where a 64mm valve earns its place.
2. Look at valve lift, not just diameter
Valve diameter is only half the story. How far the valve opens also decides how much air gets out. The Granatelli 540200 and the 540201 Ultra High Flow are both 50mm, but the 540201 lifts 0.625" against the 540200's 0.340", so it opens far more area for the air to escape.
3. Plan the spring
Pick a spring that keeps the valve shut at idle and under boost, but still lets it open fully on lift-off. Interchangeable springs or adjustable preload let you tune that to your engine's idle vacuum and boost level.
4. Check the mount
Most performance BOVs weld onto the charge pipe with a flange. Place it close to the throttle body on the cold side, after the intercooler, so it can release air quickly. Our BOV placement and reference routing guide covers location in detail.
Granatelli Blow-Off Valves at a Glance
| Part # | Size | Key feature | Springs / adjustment | Price (Nov 19, 2026) |
|---|---|---|---|---|
| 540200 | 50mm | 0.340" lift, V-band and weld flange included | 6 psi and 15 psi springs | $78.55 |
| 540201 Ultra High Flow | 50mm | 0.625" lift, weld flange and V-band clamp included | 6 psi and 15 psi springs | $219.95 |
| 540198 Viper Series | 50mm | Billet aluminum, high-flow valve | Externally adjustable spring preload | $274.31 |
| 540199 Anaconda | 64mm | Billet 6061 aluminum, black anodized, dual 1/8" NPT reference ports | Adjustable diaphragm-over-piston actuation | $344.14 |
All four are atmospheric and made in the USA. Prices may change; check each product page for the current price.
- Best value for most turbo street builds: the 540200.
- Same 50mm size, more relief flow: the 540201.
- Want to fine-tune response to your idle vacuum: the Viper 540198.
- Big turbos, high boost and centrifugal superchargers: the 64mm Anaconda 540199.
Common Blow-Off Valve Mistakes
- Running an atmospheric BOV on a MAF car without talking to your tuner. Lift-off stumbles and rich stalls are the usual result.
- Spring too soft. The valve leaks at idle or under boost, and you chase a "boost leak" that's really the BOV.
- Spring too stiff. The valve doesn't open fully, and you still hear surge on lift-off.
- Reference line in the wrong place. The line has to see manifold pressure after the throttle body, or the valve can't tell when the throttle closed.
- Undersizing on a big turbo. A small valve on a large compressor can't release air fast enough.
- Buying for the sound. The noise is a side effect. Pick the valve for airflow and your engine management first.
Frequently Asked Questions
What does a blow-off valve do?
It releases pressurized air from the charge pipe when the throttle closes under boost, so the air doesn't push back through the turbo's compressor. That reduces compressor surge and keeps throttle transitions clean.
Does a blow-off valve add horsepower?
No. A BOV protects the turbo and helps the boost system behave between throttle events. It doesn't make power by itself.
Do I need a blow-off valve on my turbo car?
Most turbocharged engines with a throttle body use a blow-off or recirculating valve. Many factory turbo cars already have a recirculating valve; aftermarket turbo kits and custom builds usually need one added.
What's the difference between a blow-off valve and a diverter valve?
Both release boost when the throttle closes. A blow-off valve usually vents to the atmosphere; a diverter (recirculating) valve routes the air back into the intake ahead of the turbo.
What is compressor surge?
Compressor surge is trapped boost reversing direction and pushing against the spinning compressor wheel after the throttle closes. It sounds like a flutter and puts reverse load on the turbo.
Where should a blow-off valve be mounted?
On the cold-side charge pipe, after the intercooler and close to the throttle body, with the reference line connected to the intake manifold after the throttle.
What size blow-off valve do I need?
A 50mm BOV covers most street and street/strip turbo builds. Large turbos, high boost, big charge piping and centrifugal superchargers often call for a 64mm valve like the Granatelli Anaconda.
The Bottom Line
A blow-off valve is cheap insurance for your turbo. It gives trapped boost a way out when you lift, keeps surge off the compressor and helps the car pick boost back up cleanly. Size it to your airflow, match the spring to your engine, and make sure your engine management is happy with an atmospheric valve.
Granatelli Motor Sports builds four atmospheric blow-off valves in Oxnard, California, from the $78.55 540200 to the 64mm Anaconda. Free shipping on orders over $100, and orders placed before 3:30 PM Pacific ship the same day.
Shop Granatelli 50mm & 64mm Blow-Off Valves →
Building out the whole boost system? See our blow-off valves and wastegates.
Written by JoJo Granatelli — third generation at Granatelli Motor Sports in Oxnard, California.

